New

Home Decor

Mason Jar Lamp

STEPS

8

SKILL LEVEL

This is another project which you can alter to fit your space and style. We chose to make a lamp around 4 feet long. Before getting started- one extra safety tip we'd like to point out: To avoid overheating the lamp, we recommend using low-voltage LED tealights such as the Philips Imageo lights. Detailed safety & usage information on the lights can be found at: http://www.usa.philips.com/c-p/691266048/imageo-6-set.

by Dremel ®

204 PROJECTS

Supplies Needed For This Project

TOOL

9100 Fortiflex Heavy Duty Flex Shaft Tool

Model # 9100

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

Materials

  • 1

    Dremel 150 1/8" Drill Bit
  • 1

    1x6x48" Cedar
  • 1

    4' length of 1/2" copper pipe
  • 3

    3 mason jars
  • 3

    Metal Ring
  • 1

    Screwdriver
  • 15

    Small wood screws
  • 3

    Low-Voltage LED tealights

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Begin by cutting your cedar plank into three 4" by 6.5" blocks. As your material is 4" wide, measure three sections of 6.5" lengths. Clamp your material to your workbench and using your Saw-Max tool equipped with the SM500 wheel, cut along your marked lines, following the line of cut through the notch at the front of the tool.

STEP 2

Step 2

To give the blocks a more finished look, we chose to then cut each corner at a vertical angle with a quick plunge cut.

STEP 3

Step 3

Next, we cut our copper pipe into our desired lamp length, at around 4'. Measure and mark your cut, then place your pipe in a vice. Replace your SM500 blade with the SM510 Metal cutting wheel and cut along each mark.

STEP 4

Step 4

Next, we attached our Mason jar lids about 1/2" inch from the edge of each of our cedar blocks. This process works best if you first drill mounting holes near the outer edge of the mason jar lid. We made our pilot holes using the NEW Dremel FortiFlex which we keep secured above our work station. With the 150 drill bit mounted into the tool, hold the hand piece perpendicular to the jar lid and make 2 quick pilot holes opposite of each other. Next, place the metal lid ring around the lid & drill both into place with 3/4" length wood screws.

STEP 5

Step 5

Next, we threaded our block onto the pipe. To do so, we drilled holes using a 1/2" spade bit 2" from the end of the block, opposite from the mason jar lid. Slide all three blocks over the pipe into your desired positions. Before securing the blocks onto the pipe, attach the jars to the lid to be sure they're spaced far enough apart.

STEP 6

Step 6

Once you have determined your desired spacing for the wood blocks, drill a pilot hole through the back of your cedar block and into the pipe. We again used our NEW Fortiflex tool handily mounted above our work station to make the three quick pilot holes. Secure the block to the copper pipe using your drill & small wood screws.

STEP 7

Step 7

We secured a ring (a key ring or flexible metal o-ring will work) at the top of our lamp in order to hang it from a ceiling hook. The FortiFlex came in handy again! Using the same 150 drill bit, make a small hole through the top of the pipe & thread the ring through the hole.

STEP 8

Step 8

Place your low-voltage tealights into the jars & secure the jars to the mounted lids lids. Hang your lamp into place and enjoy the flickering glow!

Suggested Videos

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

Other Projects You Might Like

Ladder Golf Game
games
Ladder Golf Game

1month ago

PVC Lamp
home decor
PVC Lamp

1month ago

Basketball Backboard
games
Basketball Backboard

1month ago

Bag Toss
games
Bag Toss

3months ago

No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.