New

Furniture

Pallet Table

STEPS

4

SKILL LEVEL

Pallets come in all different shapes and sizes! In this project, we'll provide you with dimensions specific to our pallet for reference. Of course, we always encourage you to use your creativity to customize your unique project!

by Dremel ®

205 PROJECTS

Supplies Needed For This Project

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

TOOL

Multi-Max™ MM30

Model # MM30

ACCESSORY

SM600 3" Wood & Plastic Flush Cut Wheel

Model # SM600

ACCESSORY

SM510 3" Metal Cut-Off Wheel

Model # SM510

ACCESSORY

60, 120 and 240 Grit Sand Paper - Wood

Model # MM70W

Materials

  • 1

    Pallet
  • 1

    Drill
  • 1

    1 3/8" Hole Saw
  • 4

    Pieces 1" ID Galvanized Pipe
  • 4

    Floor Flanges
  • 1

    18 x 24" 26 gauge sheet metal

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

As a reminder- the dimensions you'll be making your cuts to are subject to change based on your pallet. We chose a pallet which had straight boards which were all intact. Begin by cutting your pallet down to size. To maintain the structure of your table, make sure you keep the middle beam intact. Using the SM20 & SM600 Wood & Plastic Flush Cutting Wheel, we cut our pallet down the middle, flush with the center beam.

STEP 2

Step 2

Since our table was created as a dual table & storage unit, we cut a 18 x 24" metal shelf to line the bottom, inside of the pallet. Measure the area you're lining with shelving & mark your cut on the sheet of 26 gauge sheet metal. Next, remove your SM600 Wheel you used in step 1 and replace it with the SM510C Metal Cutting wheel. With your sheet metal secured on your workbench, cut along your marked line. Tip: Let the speed of the tool do the work & do not force the blade through the metal.

STEP 3

Step 3

Give your table a smooth finish by sanding it with the NEW Dremel MM30 & 70W Sandpaper. With your tool set to high speed, make light, circular passes across the surface of the table.

STEP 4

Step 4

Next, use your drill & hole saw to create 4 holes at each corner of the table through which you’ll set the legs of your table. We used 4 pieces of 18" long 1" ID galvanized pipe to serve as each leg. Therefore, we used a 1 3/8" hole saw to create each hole, giving our legs a snug fit. Once you set each leg evenly in place, set each into a floor flange which will serve as a sturdy base to your legs.

Suggested Videos

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

Other Projects You Might Like

PVC Lights
home decor
PVC Lights

1year ago

home repair

1year ago

Birch Wood Candle Holders
home decor
Birch Wood Candle Holders

1year ago

Patio Bench
furniture
Patio Bench

1year ago

No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.