New

Organizational

Catchall Organizer

STEPS

13

SKILL LEVEL

This week we're sharing a surprise project brought to you by this month's Featured Blogger - Jamie Roubinek of Roubinek Reality. Check out her blog here for other DIY projects, recipes & much much more!

by Dremel ®

201 PROJECTS

Supplies Needed For This Project

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

TOOL

3000 Variable Speed Rotary Tool

Model # 3000

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

EZ Drum™ Mandrel

Model # EZ407SA

Materials

  • 2

    8 foot 1x4s
  • 1

    8 foot 1x2
  • 1

    1" Finishing nails
  • 10

    3/4" Screws
  • 1

    12x12 Sheet metal
  • 10

    Hose Clamps
  • 3

    Mason Jars
  • 1

    Stain of your choice
  • 1

    Foam brush

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Measure and mark your cut lines on your 1x4s, making cuts every 27 5/8" with your Dremel Saw-Max equipped with a SM500 wheel. You will need 5 slats, total. You'll also use the same tool to cut 4 1x2s 18 1/2" long.

STEP 2

Step 2

Line up your wood and check to make sure your cuts are correct. For those cuts that might be a little off, you can use the Dremel 3000 sanding attachment to sand them down to the right measurement. It's also perfect for smoothing out the rough edges of your 1x4 slats.

STEP 3

Step 3

Stain all of your wood, using your preferred stain color. For this project I used MinWax® Dark Walnut. After a few minutes, use a towel to wipe off stain that did not soak into the wood.

STEP 4

Step 4

Line your slats up along the 1x2s, using wood glue and clamps to secure them. Once your wood glue has dried, hammer your 1" nails in.

STEP 5

Step 5

Glue, clamp, and hammer in your 1x2s on to the top and bottom of the slats.

STEP 6

Step 6

Once you have decided where you would like to place your sheet metal, you will need to drill pilot holes in to your metal.

STEP 7

Step 7

Screw your metal into the wood using 3/4" screws.

STEP 8

Step 8

To frame your sheet metal, lay out your wood and find your correct measurements. I was able to cut two pieces of 1x2 at 10 3/4" and two pieces at 11 1/2". Once your wood pieces are stained, glue them down and nail them in to your wood slats.

STEP 9

Step 9

Just like you made a pilot hole in your sheet metal, you will also need to use the same bit to create a larger hole in your hose clamp. A screw will not fit through the the holes of the hose clamp.

STEP 10

Step 10

Drill a pilot hole in your wood where you would like to attach your mason jars.

STEP 11

Step 11

Screw your collar into the wood using a 3/4" screw.

STEP 12

Step 12

Place your mason jar inside the collar and tighten the hose clamp as tight as possible.

STEP 13

Step 13

Align your last three mason jars where you would like them and repeat steps 9, 10, 11, and 12

Suggested Videos

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

Other Projects You Might Like

Cutting a Drain Pipe
home repair
Cutting a Drain Pipe

1year ago

PVC Lights
home decor
PVC Lights

8months ago

Puppet Theater
games
Puppet Theater

1month ago

Catchall Organizer
organizational
Catchall Organizer

1year ago

No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

No Promotion available!

A TOOL THAT CAN DO IT ALL

Experience Dremel's most powerful oscillating tool. Featuring 7.0 amps of power and 2 new, powerful cutting blades, the Dremel Velocity is the only tool you need.