New

Kitchen

Update Kitchen Tile

STEPS

5

SKILL LEVEL

Years of wear can make your tile and grout look weathered and worn. You may even have a broken tile you'd like to remove.... Dremel tools are perfect for making updates to your tile. In this project we removed grout to replace a broken tile. You can use the same grout removal technique if you would like to simply re-grout worn or moldy tile.

by Dremel ®

204 PROJECTS

Supplies Needed For This Project

TOOL

4000 High Performance Rotary Tool

Model # 4000

TOOL

Multi-Max™ MM20

Model # MM20

ACCESSORY

MM920 24 Grit Carbide Rasp

Model # MM920

ACCESSORY

569 1/16" Carbide Grout Removal Bit

Model # 569

ACCESSORY

568 Grout Removal Attachment

Model # 568

Materials

  • 1

    Chisel
  • 1

    Grout Float
  • 1

    Tile Adhesive
  • 1

    Hammer or Rubber Mallet
  • 1

    Grout
  • 1

    Sponge

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Remove Grout

When removing wall or floor grout with your Dremel Rotary tool, the Attachment #568 makes the job easy! The attachment keeps the bit at the perfect cutting angle and guides the bit between tiles so you don't damage them. - First, you'll want to prep your tool for the job. Start by removing the nosecap of your tool completely. Next, insert the Rotary Accessory #569 and tighten with your EZ Twist Nosecap wrench or the wrench included in your tool kit. Finally, screw on the grout removal attachment firmly. You will notice that the attachment has a depth guide, allowing you to set the depth of the bit in 1/8" increments. To begin your project, loosen the thumbscrew next to the depth guide and set it to 1/8" (the most shallow) depth.

STEP 2

Remove Grout

- Plug in your tool and set it to 15,000 to 20,000 RPMs. That is switch setting 15 or 20 on your 4000 tool. If you are not using a 4000 tool, refer to the owners manual for your model on Dremel.com to determine the switch setting that achieves 15,000 to 20,000 RPMs. - Using a pulling motion, work the bit through the grout, letting the attachment guide you through the tiles without nicking them. - Make several passes through the grout if necessary. On your first pass, set the depth of the guide on the shallow side, to 1/8". Don't set the depth of your guide too deep on your first pass, as this may damage your bit. On your second or third pass, set the depth of your guide even deeper. - When working in a corner, unplug your tool, remove the attachment and replace it with your nosecap. Aim to remove grout to the same depth as you had done with the grout removal attachment, making several passes if necessary.

STEP 3

Remove Tile

If you are removing grout to replace damaged or worn tile you will need to pry the old tile off. - Here we used a chisel and added some force by lightly tapping it with a hammer. - Having removed the grout around the tile will make this process easier, but do remember to continue wearing eye protection to avoid any debris getting into your eyes.

STEP 4

Prep Surface for New Tile

Once you have removed the grout around your tile, it is time to get out your Dremel Multi-Max tool. Smoothing down the surface that you will be setting your new tile in will help make sure your tiles are set on an even surface. - Attach a Carbide Rasp #920, plug in your Multi-Max and set it to full speed. Working in slow, even strokes, grind and shape the adhesives to create a smooth, even surface. The shape of the accessory will allow you to fit into corners to make sure the entire area is smooth.

STEP 5

Re-grout and Wipe Off with Sponge

adhesive to the area you smoothed down. - Set the new tile in its place, keeping an even space between the new tile and surrounding tiles. Allow to set overnight. - Once the tile is set, re-grout with similar tile grout as was used around your other tiles for a uniform look. Using a grout float, force grout into the seams which need to be filled. Allow to dry then wipe off excess grout from surrounding tiles with a clean, damp sponge.

Suggested Videos

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

Other Projects You Might Like

New Year Decoration
3d
New Year Decoration

2months ago

DIY Ornaments
seasonal
DIY Ornaments

2months ago

PVC Lights
home decor
PVC Lights

2months ago

Snowflakes
seasonal
Snowflakes

2months ago

No Promotion available!

A TOOL THAT CAN DO IT ALL

Experience Dremel's most powerful oscillating tool. Featuring 7.0 amps of power and 2 new, powerful cutting blades, the Dremel Velocity is the only tool you need.

No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.