New

Craft and Hobby

Diorama

STEPS

8

SKILL LEVEL

Display your favorite holiday pictures & collectables with a unique decorative wall shelf. We constructed ours out of extra building materials we had on hand!

by Dremel ®

204 PROJECTS

Supplies Needed For This Project

TOOL

4200 High-Performance Rotary Tool

Model # 4200

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

ACCESSORY

628-01 Drill Bit Set

Model # 628-01

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

SM600 3" Wood & Plastic Flush Cut Wheel

Model # SM600

ACCESSORY

SM510 3" Metal Cut-Off Wheel

Model # SM510

Materials

  • 9

    Various-sized sports balls (ie tennis ball, mini basket ball, ping-pong ball)
  • 1

    48" length 1/8" metal rod
  • 1

    15" x 40" Luan
  • 1

    24" length of 2x4"
  • 1

    Hot Glue Gun
  • 1

    Craft Paint & Spray Paint
  • 1

    String Lights

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Begin by making the base of your diorama to which you'll mount your various "planets" we made our diorama 24" wide. You may already have a piece of 2x4 cut to this length. If not, no problem! The Dremel Saw –Max equipped with the SM600 Wood & Plastic Flush-Cutting Blade along with the 2x4 Cutting Guide can help you get the job done. Measure and mark a 24" length on your 2x4. Place the guide near your measurement marks. Leave about an 1/8 inch between the guide and line to accommodate for the kerf of the wheel and its slight offset. Clamp the guide in place. Make your first pass, then flip the board over to complete the cut all the way through the 2x4 on your second pass.

STEP 2

Step 2

Next, drill holes in the base for your metal stands you'll be cutting in later steps. Measure and mark the placement of your stands based on the width of your "planets", ensuring they will not overlap each other once assembled. Insert the Dremel 1/8" Drill Bit into your 4200 tool, set the tool to high speed and, holding the tool perpendicular to the 2x4, plunge 1/2" deep holes into each of your marked points.

STEP 3

Step 3

Next, it is time to cut your various planet stands. We varied our heights based on the size of planets to ensure a well-spaced fit/ We measured and marked varying lengths in a piece of 48" long 1/8" metal rod. With the rod clamped in a vice, we cut along our marked lines using our Saw-Max Tool equipped with an SM510 Metal Cutting Blade.

STEP 4

Step 4

Using wood glue, we secured each rod into its designated hole drilled in step 2.

STEP 5

Step 5

Next, drill holes into each of the balls you plan to mount to the stands. Due to the weight and size of our basketball, we designated it as the sun and did not secure it onto a stand. However, we found that the weight and size of tennis balls, foam balls, super balls and ping pong balls worked well to mount to the stands. Need a tip for Saturn's rings? We used a carry-out box! With your chosen planets secured in a vice, mark a center point which you'd like to mount to the stand. With your 1/8 bit still secured in your 4200 tool, set the tool to high speed and make a quick plunge cut in each of your marked points.

STEP 6

Step 6

Next, we created the side boards and a backboard for our diorama. You may choose not to add this step, however, we thought it was necessary for the addition of the stars at the end! If you plan to use our dimensions for your diorama, we recommend making the following cuts in 1/4" luan: • 2 side pieces at 15" tall x 9" wide • 1 back piece at 15" tall x 24" wide Measure and mark your lines of cut. Mount the SM500 wheel on your Saw-Max and follow along your marks.

STEP 7

Step 7

Next, paint your back and side walls. If you choose to insert lights through the back wall, we recommend using your 4200 with the 1/8 Drill bit to plunge a hole for each light into the wall before painting it.

STEP 8

Step 8

Set your lighting into your back wall and finally, glue your side and back wall pieces together with hot glue or wood glue.

Suggested Videos

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

Other Projects You Might Like

PVC Lights
home decor
PVC Lights

1month ago

Update Kitchen Tile
kitchen
Update Kitchen Tile

1month ago

Bean Bag Toss Game
games
Bean Bag Toss Game

1month ago

Decorative Shelves
home decor
Decorative Shelves

1month ago

No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.