New

Games

Bag Toss

STEPS

4

SKILL LEVEL

Try a new take on an old favorite. Bag toss tic-tac-toe makes for a great outdoor game or indoor game year-round

by Dremel ®

203 PROJECTS

Supplies Needed For This Project

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

TOOL

Multi-Max™ MM40

Model # MM40

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

60, 120 and 240 Grit Sand Paper - Wood

Model # MM70W

ACCESSORY

MM482 1-1/4” Wood & Metal Flush Cut Blade

Model # MM482

Materials

  • 1

    24" x 24" plywood 1/4" thick
  • 1

    sheet 24" x 48" plywood 1/2" thick
  • 1

    1 x 4 x 96" pine board
  • 1

    Wood Glue
  • 1

    Hammer & Finishing Nails
  • 1

    Thin Wood Screws
  • 1

    Screwdriver
  • 1

    Paint
  • 5

    beanbags of color #1
  • 5

    beanbags of color #2

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Begin by cutting the interior box sides from the 1/2" plywood by cutting 3.5" strips across the entire sheet. From these strips you'll need to cut 18 pieces at 6.5" long and 18 pieces at 7.5" long. Measure and mark your cuts. Onto your plywood material. With your material clamped to your workbench, cut along your marked strips using a Dremel Saw-Max tool equipped with the Wood & Plastic SM500 blade. You'll love how quickly and easily you can make these cuts with this one-handed tool.

STEP 2

Step 2

Using your Multi-Max tool & MM70W Sandpaper, smooth out any rough surface areas on the pieces you just cut. Build the 9 boxes for the inside of the board by gluing with wood glue. Allow the boxes to dry securely using clamps.

STEP 3

Step 3

Lay out the boxes in a 3x3 tic-tac-toe pattern and measure the remaining side lengths. We measured our top length at 24" and our side height at 22-1/2". Your measurements may vary slightly depending on how your interior boxes set. Mark your required lines of cut in the 1/4" pine boards. Using your Dremel Saw-Max tool equipped with the same SM500 blade, cut along your marked lines. Set the outer box again with wood glue. We hammered finishing nails into all 4 corners for an extra-secure fit.

STEP 4

Step 4

Finally, using your Saw-Max SM500 cut a bottom panel out of your 1/4" plywood and secure with screws around the outer frame. Be sure to leave your center divider boxes removable for painting and decorating. Our bottom panel measured to 24" by 24"

Suggested Videos

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

Other Projects You Might Like

Portable Horseshoe Pit
games
Portable Horseshoe Pit

1year ago

Etched Candle
home decor
Etched Candle

7months ago

Terra Cotta Patio Lights
art & sculptural
Terra Cotta Patio Lights

9months ago

Custom Headboard
home decor
Custom Headboard

1month ago

No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.