Create a Fruit and Vegetable Wall

How to create a fruit and vegetable wall

    You need

    Step By Step Instructions


    Measure your wall and draw up your design

    You need:

    Measure the space on your wall and draw up your design on a sheet of paper. Our design measured 54" high x 20.5" wide.


    Using DSM20 and DSM510  cut 6 individual aluminum rods

    You need:

    Then, use your Dremel DSM20 compact saw and the DSM510 Metal and Plastic Cut-Off Wheel to cut six individual aluminum rods to 20" gripping them firmly into either the Dremel Project Table or a similar workstation. These will become the hoops, each sized 6.5" in external diameter, to hold your plant pots.


    Weld together the two ends of the hoop using the Dremel Versaflame

    You need:

    Then, bend each length into an individual circle. Screw four metal brackets into your workbench to hold the size of hoop you want to weld. Weld together the two ends of the hoop using the Dremel Versaflame. In order to do this, first, clean up the faces using your Dremel 3000 with a Dremel stainless steel wire brush 530 to remove oxidization, dust etc. Then, heat each of the two ends of the hoop to melting point using your Dremel Versaflame. Lay a bead of the welding rod onto each face of the hoop. When the end of the hoop is hot enough, the welding rod will melt onto the end of the hoop.


    You need:

    Then, while the bead of welding rod is still molten, scrape through the molten welding rod with a stainless steel abrading rod to break through the oxidation formed underneath the molten bead of weld rod. This ensures that the bead of welding rod merges with the aluminium. Close up the hoop, and clamp in position using a Dremel bar clamp or similar, then heat up until it reaches the welding rod’s melting point again and the two mating faces will fuse together. If necessary add more welding rod. There are some good tutorials on YouTube to help you do this.


    Solder 3 feet length of aluminum rod to hoop and repeat

    You need:

    Take 3 feet length of aluminum rod to form one of your trellis’s vertical lines. Fix your first hoop at 2.5", fix your second hoop at 20", attach your third hoop at 37". Repeat this process on another 3 feet of aluminum rod.


    Weld the horizontal struts onto the vertical struts with Dremel Versaflame

    You need:

    Now, cut 3 x 20" lengths of aluminium rod using your Dremel DSM20 and Metal and Plastic Cut-Off Wheel, as before. These will become the horizontal struts. Mark up where the vertical struts will go onto your horizontal struts at 5", 10" and 15". Also, mark up the vertical struts, which you have welded with hoops, at 0", 17.5" and 34.5" to intersect with the horizontal struts. Now weld the horizontal struts onto the vertical struts.


    You need:

    Then, take a 3 foot length of aluminium rod x 2 and using your Dremel Versaflame weld to either side to make the external side vertical struts. Take another 3 foot length of aluminium rod and bend it into an arch for the top of the structure. We used a dustbin lid to bend it around. Weld the ends to the external side vertical struts. Take a 3 foot length of aluminium rod, then cut a piece x 14.5" and weld together to create the center upright and weld all intersecting points. Add two top upright 13" sections and weld. Finally, add 4.5" support struts – two per hoop x 6 hoops giving you 12 struts in total.


    Using Dremel 3000 cut out leaf shapes from aluminum sheet

    You need:

    Once you have your structure, make a leaf on a twig and solder to the top of the arch. To do this, cut one x 31.5" aluminium rod, bend it by hand in the middle into a V and then into shapes on the ends which mimic stalks, onto which you attach metal leaves. To make the leaves, mark up and cut out metal diamond-shaped leaf shapes from very thin sheet aluminium 1mm thick using your Dremel 3000, Dremel EZ SpeedClic mandrel SC402, metal cutting wheel SC456, then weld them onto the aluminium rod stalks using your Dremel Versaflame.


    Plant up your glazed painted terracotta or plastic pots with fruit

    You need:

    Either leave silver or spray paint black for contrast against the wall. Mount your metal structure onto the wall using either hooks or metal brackets. Plant up your glazed painted terracotta or plastic pots with fruits or vegetables.