How to Build Your Own Box Kite

How to Build Your Own Box Kite

  • Difficulty
    Easy

Introduction

From kids to grandparents, flying a kite is great fun no matter your age. In this easy step-by-step guide, we’ll show you how to build your own box kite using only basic materials and your trusty Dremel Multi-Tool and accessories. Then you can either get creative with your kite’s colourful design using spray paint or keep it simple and dive straight into the challenge of getting your homemade kite up in the air.

You need
  • Scissors
  • Paint spray can
  • Packing tape
  • Cable ties or wire
  • Flying line
  • 4 x 90 cm dowel rods
L: Length, W: Width, H: Height, D: Diameter

Let's go - step by step

Step 1 7

Cut the dowel rods

Use your Dremel 3000 and the EZ SpeedClic Plastic Cutting Wheels (SC476) to easily cut dowels to the lengths you need

First, use your Dremel Multi-Tool and an EZ SpeedClic Plastic Cutting Wheel (SC476) to cut the dowels to size. Cut 4 dowel rods to a length of 90 cm each. These will be used for the sides of your box kite. Then cut 4 more dowel rods to 50 cm. These will form the kite’s crosspieces. That’s done – now let’s move on to step 2!

Step 2 7

Cut the vinyl tubing to size

You can bore a hole through the vinyl tubing pieces in no time with your Dremel Multi-Tool and the High Speed Cutter 6,4 mm (125)

Next, swap out your cutting wheel with the High Speed Cutter 6,4 mm (125), and cut the vinyl tubing into 5 cm pieces. You’ll need 8 of them. Then, bore a hole through each tubing piece about 2 cm from the end. The holes should be just big enough for the dowel rod to tightly fit into them.

Step 3 7

Slide the vinyl tubing pieces over the dowel rods

Slide the vinyl tubing pieces over the 90 cm dowel rods to create joints

Now, with all the vinyl tubing pieces fully prepped, we’ll be using them as joints for your dowel rods. Slide them over the 90 cm dowel rods, placing them approximately 15 cm from each end, as shown in the image. Piece of cake, right?

Step 4 7

Prepare the plastic sheeting

Cut the plastic sheeting into 2 pieces measuring 30 x 150 cm

For this next step you’ll need your plastic sheeting. No worries if you can’t get hold of some. A good alternative would be to use a dust sheet  – even a bin bag would do! Cut a piece of sheeting measuring 30 x 150 cm. Use packing tape to stick the shortest sides together to form a loop. Next, fold the plastic sheet in half lengthwise. With scissors, cut a notch in the middle and at either end to create holes for attaching your tubes. Do the same with another 30 x 150 cm piece of sheeting. Well done, you’re almost ready for take-off!

Step 5 7

Position the 90 cm dowel rods

Vinyl joints are added on the inside of the cuts in the plastic sheet and safely secured with packing tape

Position one of the 90 cm dowel rods inside the cut plastic sheet, lining up the vinyl tubing joint with the one of the cut-out notches. Secure the rod in place with packing tape. Repeat for the remaining 3 corners, as shown. Hint: it’s easier with a helping hand! Secure the second sheet to the opposite ends of the rods to complete the outside of the kite.

Step 6 7

Insert the dowel rods into the vinyl tubing joints

Dowel rods are inserted into vinyl tubing joints and tightly secured with wire or cable ties

Your box kite is about to take shape! Insert the 50 cm dowel rods that you cut in step 1 into the vinyl tubing joints to form two crosses. This step can be a bit tricky: you’ll need to carefully bend 2 of the 4 rods into place to stretch the outside framework. Secure the intersection of each pair of dowel rods with wire or cable ties, as shown. Is everything tightly secured? Great! Now onto the final step of this project.

Step 7 7

Decorate your homemade box kite

A beautiful red and blue homemade box kite taking off

Time to add some finishing touches! You can decorate your kite however you’d like: we spray-painted ours in bright red and blue to keep it light and airy, but you can pick any colour and create any pattern you like. Just get creative. The final thing you need to do is attach a flying line to the lower notch of one of the 90 cm dowel rods, and you are ready to fly!

Undertaking of these projects are to be executed by adults only and entirely at your own risk. Dremel and Bosch can in no way be held accountable for any damage that may unexpectedly arise as a result of the use of these products.